Installation & Care Tips 

💡Things to Keep in Mind

• After transportation, let the refrigerator stand upright for 4–24 hours before plugging it in.
• Leave sufficient space around the appliance for proper airflow.
• Do not place it next to an oven or stove.
• Set the refrigerator temperature to approximately 4°C (39°F).
• Set the freezer temperature to approximately -18°C (0°F).

🛠 Installation Tips

• After transportation, allow the refrigerator to stand upright for 24 hours before switching it on.
• Leave sufficient space around the appliance for proper airflow.
• Place the refrigerator on a level surface.

💡Things to Keep in Mind

• Ensure the washing machine is perfectly level.
• Remove the transport bolts before first use.
• Use a dedicated grounded electrical outlet.
• Check that the water pressure is sufficient.
• Clean the lint filter and drain pump regularly.

🛠 Installation Tips

• For front-load washers, remove the transport bolts before installing the washing machine.
• For top-load washers, remove all protective foam and plastic covers before first use.
• Ensure the washing machine is perfectly level. Adjust all four feet to prevent excessive vibration.
• The drain hose should be installed at a minimum height of 60 cm from the floor.
• A hydrofoor (water pressure system) is recommended to ensure adequate water supply and proper performance.

💡Things to Keep in Mind

• Ensure the dryer has adequate ventilation.
• Empty the condensate water tank regularly (for condenser dryers).
• Clean the lint filter after every drying cycle.
• Avoid overloading the dryer.

🛠 Installation Tips

• A 220V dryer requires:
  
  • 220V power supply
  • 4 x 4 mm² electrical cable
  • 2-phase, neutral and earth connection
• Installation should include either:
  
  • a dedicated disconnect switch, or
  • a Perilex outlet.
• Ensure the installation area is well ventilated.

💡Things to Keep in Mind

• Connect the dishwasher correctly to both the water supply and drain.
• Use dishwasher salt if required.
• Use rinse aid for improved drying performance.
• Clean the filters regularly.
• Do not overload the dishwasher.

🛠 Installation Tips

• European dishwashers must be connected to a cold water supply, as they have their own heating element.
• American dishwashers must be connected to a hot water supply.
• Do not remove the insulating fabric (blanket) around the dishwasher. It helps reduce noise and improves thermal insulation.
• Ensure both the water supply and drain hose are correctly connected before first use.

💡Things to Keep in Mind

• Install only with an approved gas connection.
• Check for gas leaks after installation.
• Ensure the kitchen is well ventilated.
• Keep flammable materials away from the appliance.

💡Things to Keep in Mind

• Use cookware with a flat base for even heat distribution.
• Match the cookware size to the cooking zone for better efficiency.
• Clean spills promptly to keep the cooking surface in good condition.
• Allow the cooktop to cool completely before cleaning.
• Keep flammable items away from the cooking surface.

🛠 Installation Tips Gas Cooktop

• American and European models may require the burner jets (nozzles) to be changed to match the local gas type.
• The gas regulator must be properly adjusted during installation.
• Conversion from butane gas to propane gas may be required.
• Built-in gas cooktops must not be completely sealed into the countertop, as proper ventilation is required.
• Professional installation is recommended.

🛠 Installation Tips Electric Cooktop

• Requires a 220V power supply.
• Requires a 4 × 4 mm² electrical cable.
• Requires a 2-phase, neutral, and earth connection.
• Installation should be carried out by a qualified electrician and in accordance with local electrical regulations.

💡Things to Keep in Mind

• Use a dedicated electrical circuit.
• Leave sufficient clearance around the oven for ventilation.
• Do not install the oven directly against a wall.
• Run the oven empty before first use to burn off any manufacturing residues.

🛠 Installation Tips

• Requires:
  
  • 220V power supply
  • 4 x 4 mm² electrical cable
  • 2-phase, neutral and earth connection.
• Built-in ovens should never be installed directly on the cabinet base. Adequate clearance must be provided underneath for proper ventilation.
• Follow the installation dimensions provided in the user manual.

💡Things to Keep in Mind

• Leave sufficient space around the appliance for proper airflow
• Use only microwave-safe cookware.
• Do not block the ventilation openings.
• Never use metal containers or utensils unless specifically approved.

💡Things to Keep in Mind

• Place the dispenser on a flat, stable surface.
• Let it rest for several hours after transportation before use.
• Clean the water reservoir regularly.
• Always use clean water bottles.

💡Things to Keep in Mind

• Have the unit installed by a qualified technician.
• Ensure the wall can support the weight of the water heater.
• Install a safety relief valve.
• Check that the water pressure is within the recommended range.

💡Things to Keep in Mind

• Leave sufficient space around the appliance for proper airflow
• Place it on a heat-resistant surface.
• Clean the basket after every use.
• Do not block the air outlet.

💡Things to Keep in Mind

• Do not overfill the blender.
• Make sure the lid is securely closed before blending.
• Do not blend boiling liquids unless the appliance is specifically designed for it.
• Handle and clean the blades with care.

💡Things to Keep in Mind

• Use filtered water whenever possible.
• Descale the machine regularly.
• Clean the brew group if applicable.
• Empty the drip tray regularly.

nibh nisi a suspendisse a.

💡Things to Keep in Mind

• Do not fill above the maximum water level.
• Avoid using low-quality extension cords.
• Descale the kettle regularly

💡Things to Keep in Mind

• Use the correct water pressure.
• Never operate the pump without water.
• Use only suitable extension hoses and accessories.
• Store the unit in a frost-free environment.

💡Things to Keep in Mind

• Empty the dust container regularly.
• Clean or replace the filters as recommended.
• Use the appropriate floor attachment for the surface being cleaned.

💡Things to Keep in Mind

• Place the fan on a stable, level surface.
• Leave at least 50 cm of free space around the fan.
• Clean the fan blades regularly to maintain optimal airflow.